CSI Aviation job details and career information

Aircraft Mechanic Hot

Location
Santa Fe, New Mexico
Wage
Hourly
Job ID
12607421346
Posted
2020-9-16

AIRCRAFT MECHANIC BEECHCRAFT KING AIR AND 1900 SERIES AIRCRAFT (full time w/ benefits)

Work location is at the Albuquerque International Airport (KABQ). No relocation available.


Job Summary

Early career professional approximately 3-5 years of experience required. Participate in maintenance team efforts to achieve and maintain high aircraft readiness rates. Maintain King Air and 1900 aircraft types. Set the example in word and deed to establish a culture of safety. Conforms and complies with air carrier FAA and international flight procedures and regulations ensuring aircraft is airworthy and in compliance with with safety management and other policies. Coordinate with air carrier dispatch and flight department to ensure all organizational requirements are satisfied. Completes initial and periodic training required to maintain compliance with organizational FAA and international regulations. Supports and enforces hazardous material safety personnel protective equipment use and environmental stewardship. Reports to the Director of Maintenance.

Essential Tasks/Functions:

Examine and inspect aircraft components including landing gear hydraulic systems and deicers to locate cracks breaks leaks or other problems.

Launch and recover aircraft on a daily basis or as required

Conduct routine and special inspections as required by regulations.

Read and interpret maintenance manuals service bulletins and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.

Maintain repair logs documenting all preventive and corrective aircraft maintenance.

Inspect airframes for wear or other defects.

Measure parts for wear using precision instruments.

Obtain fuel and oil samples and check them for contamination.

Maintain repair and rebuild aircraft structures functional components and parts such as wings and fuselage rigging hydraulic units oxygen systems fuel systems electrical systems gaskets and seals.

Replace or repair worn defective or damaged components using hand tools gauges and testing equipment.

Read and interpret pilots descriptions of problems to diagnose causes.

Test operation of engines and other systems.

Measure the tension of control cables.

Remove or install aircraft engines using hoists or forklift trucks.

Assemble and install electrical plumbing mechanical hydraulic and structural components and accessories using hand or power tools.

Locate and mark dimensions and reference lines on defective or replacement parts using templates scribes compasses and steel rules.

Service and maintain aircraft and related apparatus by performing activities such as cleaning screens and lubricating moving parts.

Clean refuel and change oil in line service aircraft.

Trim and shape replacement body sections to specified sizes and fits and secure sections in place using adhesives hand tools and power tools.

Accompany aircraft on flights to make in-flight adjustments and corrections.

Remove or cut out defective parts or drill holes to gain access to internal defects or damage using drills and punches.

Install and align repaired or replacement parts for subsequent riveting or welding using clamps and wrenches.

Inventory and requisition or order supplies parts materials and equipment.

Clean strip prime and sand structural surfaces and materials to prepare them for bonding.

Communicate with other workers to coordinate fitting and alignment of heavy parts or to facilitate processing of repair parts.

Examine engines through specially designed openings while working from ladders or scaffolds or use hoists or lifts to remove the entire engine from an aircraft.

Check for corrosion distortion and invisible cracks in the fuselage wings and tail.

Inspect parts such as turbine blades for corrosion wear warping cracks and leaks using precision measuring instruments.

Cure bonded structures using portable or stationary curing equipment.

Listen to operating engines to detect and diagnose malfunctions.

Clean engines sediment bulk and screens.

Determine repair limits for engine hot section parts.

Prepare and paint aircraft surfaces.

JOB REQUIREMENTS

Minimum Requirements:

Education: N/A

Professional Licensure: Airframe and Powerplant (A&P) License

Background: Must pass a commercial background investigation

Experience: Three years of prior Aircraft Mechanic experience. Experience with turbo-prop aircraft and turbine engines. Customer Service experience working with internal customers.

Computer Skills: Microsoft office: Word Excel and Power Point

Other:

Excellent communication and interpersonal skills

Highly organized with attention to detail

Good time management skills

Professional demeanor and appearance


Preferred Qualifications:

Education: AA

Professional Licensure/Certifications: Prior aircraft run up authorization

Background: N/A

Training: Trained on Beechcraft King Air series and/or 1900 aircraft.

Experience: More than three years of prior Aircraft Mechanic experience. Experience with Beechcraft King Air series and/or 1900 aircraft. Military Aviation Industry.

Please attach Resume.

CSI Aviation Inc. is an Equal Opportunity/Affirmative Action employer. All qualified applicants will receive consideration for employment without regard to race color religion sex sexual orientation gender identity or national origin.

Aircraft Mechanic Santa Fe NM

Aircraft Mechanic I C 12 king Air Ap Santa Fe NM

Aircraft Mechanic I C 12 king Air Ap With Security Clearance Santa Fe NM

Aircraft Mechanic I Alse Technician Alamogordo NM

Mechanic 3 Avionics Or E e Assistant Section Lead Non Union Sca Holloman Afb NM

Mechanic 3 Avionics Or E e Assistant Section Lead Non Union Sca With Securi Holloman Afb NM

Aircraft Survival Flight Equipment Repairer Kirtland Afb NM

Aircraft Technician Roswell NM

Aircraft Technician Roswell NM

Cbp Aircraft Mechanic Albuquerque Nm Albuquerque NM

The following jobs have been promoted on the Aviation Ad Network and are to be considered - current, newsworthy aviation employment information (FYI). No guarantee is made as to the accuracy, completeness or timeliness of any information, projections or opinions in announcements obtained through the promoted jobs. The information contained in this announcement is compiled for the convenience of site visitors and is accepted by the site visitor on the condition that errors or omissions are not the responsibility of Avjobs and shall not be made the basis for any claim, demand or cause of action. Please visit this companys web site for additional details and information. Please reference Avjobs when applying.

Top Employer CSI Aviation Jobs
Website
www.avjobs.com/companies
Job Feed
View
News Feed
View
List All CSI Aviation Jobs

Don't wait, apply today.
We can't wait to receive your resume.

CSI Aviation is accepting resumes and actively recruiting for this Aircraft Mechanic position in Santa Fe, New Mexico. Be sure to send your resume using the "Apply Now" button or by following the application instructions provided by the employer.

Aircraft Mechanic

Location: Santa Fe NM

Industry: Aviation
Occupational Category: AP Mechanic
Hours: Full-time, 40 hours per week
Salary: USD 0

Description: CSI Aviation seeks a Aircraft Mechanic.

AIRCRAFT MECHANIC BEECHCRAFT KING AIR AND 1900 SERIES AIRCRAFT (full time w/ benefits)

Work location is at the Albuquerque International Airport (KABQ). No relocation available.


Job Summary

Early career professional approximately 3-5 years of experience required. Participate in maintenance team efforts to achieve and maintain high aircraft readiness rates. Maintain King Air and 1900 aircraft types. Set the example in word and deed to establish a culture of safety. Conforms and complies with air carrier FAA and international flight procedures and regulations ensuring aircraft is airworthy and in compliance with with safety management and other policies. Coordinate with air carrier dispatch and flight department to ensure all organizational requirements are satisfied. Completes initial and periodic training required to maintain compliance with organizational FAA and international regulations. Supports and enforces hazardous material safety personnel protective equipment use and environmental stewardship. Reports to the Director of Maintenance.

Essential Tasks/Functions:

Examine and inspect aircraft components including landing gear hydraulic systems and deicers to locate cracks breaks leaks or other problems.

Launch and recover aircraft on a daily basis or as required

Conduct routine and special inspections as required by regulations.

Read and interpret maintenance manuals service bulletins and other specifications to determine the feasibility and method of repairing or replacing malfunctioning or damaged components.

Maintain repair logs documenting all preventive and corrective aircraft maintenance.

Inspect airframes for wear or other defects.

Measure parts for wear using precision instruments.

Obtain fuel and oil samples and check them for contamination.

Maintain repair and rebuild aircraft structures functional components and parts such as wings and fuselage rigging hydraulic units oxygen systems fuel systems electrical systems gaskets and seals.

Replace or repair worn defective or damaged components using hand tools gauges and testing equipment.

Read and interpret pilots descriptions of problems to diagnose causes.

Test operation of engines and other systems.

Measure the tension of control cables.

Remove or install aircraft engines using hoists or forklift trucks.

Assemble and install electrical plumbing mechanical hydraulic and structural components and accessories using hand or power tools.

Locate and mark dimensions and reference lines on defective or replacement parts using templates scribes compasses and steel rules.

Service and maintain aircraft and related apparatus by performing activities such as cleaning screens and lubricating moving parts.

Clean refuel and change oil in line service aircraft.

Trim and shape replacement body sections to specified sizes and fits and secure sections in place using adhesives hand tools and power tools.

Accompany aircraft on flights to make in-flight adjustments and corrections.

Remove or cut out defective parts or drill holes to gain access to internal defects or damage using drills and punches.

Install and align repaired or replacement parts for subsequent riveting or welding using clamps and wrenches.

Inventory and requisition or order supplies parts materials and equipment.

Clean strip prime and sand structural surfaces and materials to prepare them for bonding.

Communicate with other workers to coordinate fitting and alignment of heavy parts or to facilitate processing of repair parts.

Examine engines through specially designed openings while working from ladders or scaffolds or use hoists or lifts to remove the entire engine from an aircraft.

Check for corrosion distortion and invisible cracks in the fuselage wings and tail.

Inspect parts such as turbine blades for corrosion wear warping cracks and leaks using precision measuring instruments.

Cure bonded structures using portable or stationary curing equipment.

Listen to operating engines to detect and diagnose malfunctions.

Clean engines sediment bulk and screens.

Determine repair limits for engine hot section parts.

Prepare and paint aircraft surfaces.

JOB REQUIREMENTS

Minimum Requirements:

Education: N/A

Professional Licensure: Airframe and Powerplant (A&P) License

Background: Must pass a commercial background investigation

Experience: Three years of prior Aircraft Mechanic experience. Experience with turbo-prop aircraft and turbine engines. Customer Service experience working with internal customers.

Computer Skills: Microsoft office: Word Excel and Power Point

Other:

Excellent communication and interpersonal skills

Highly organized with attention to detail

Good time management skills

Professional demeanor and appearance


Preferred Qualifications:

Education: AA

Professional Licensure/Certifications: Prior aircraft run up authorization

Background: N/A

Training: Trained on Beechcraft King Air series and/or 1900 aircraft.

Experience: More than three years of prior Aircraft Mechanic experience. Experience with Beechcraft King Air series and/or 1900 aircraft. Military Aviation Industry.

Please attach Resume.

CSI Aviation Inc. is an Equal Opportunity/Affirmative Action employer. All qualified applicants will receive consideration for employment without regard to race color religion sex sexual orientation gender identity or national origin.

Responsibilities:

Educational requirements:

Experience requirements:

Desired Skills:

Qualifications:

Benefits:

Incentives:

Date Posted: 2020-9-16

Please Apply by: 2020-10-2