Let employers find you
2026-3-24
Berkeley, MO
plication of primary Radar Cross Section (RCS) nonstructural parasitic treatments to aircraft inner MOLD line (IML) and outer MOLD line (OML) surfaces. · Typical treatments include application of Radar Absorbing Material (RAM). Conductive material Resistive Material, Multilayer materials and tapered resistive treatments using a variety of applications. Performance of Secondary RCS processes including: fairing of OML surfaces with sealant and fairing compounds, repair of MOLD line Form-In-Place (FIP) seals and permanent butt joints
2026-3-23
Edwards Afb, CA
cated at Edwards AFB CA and Palmdale CA. Duties Responsible for all aircraft low observable outer MOLD line structures materials and applications. You will prepare composite or metallic surfaces for coating applications by performing various operations such as sanding stripping applying vacuum performing porosity testing masking and other preparation tasks. You will also mix and apply sealants gap fillers and any other required processes prior to paint which may require the use of heating devices. Mix and apply paints and other coatings at the proper spraying consisten
2026-3-9
Palmdale, CA
ning proper placement, and laying up composite, plastic and metal parts and adhesives onto tools or MOLDs. Prepares parts for bagging, including placement of bleeders, thermocouples, probes and vacuum connections, checks seals on completed bagged parts for leaks. Sets up assemblies and parts in various types of processing and curing equipment such as an autoclave, oven or platen press in order to obtain desired set and cure. Operates autoclave controls to obtain and maintain proper temperature, pressure, and time cycle in accordance with engineering materials process specifica
2026-3-4
Seal Beach, CA
to tooling, including casting, machining, forging, sheet metal fabrication, tube bending, welding, MOLDing, composite layup and assembly to support Supply Chain Utilize understanding of the different part commodities/part build strategies and what tool types are generally used for each commodity Understanding of the need for periodic tool inspections and audits and ability to execute them Articulate technical details relative to fabrication methods and tools required Utilize a basic understanding of Loft Engineering Utilize knowledge of the use of Master Toolin
2026-3-23
Auburn, WA
& Die Maker. 2 years of experience with hydraulics and pneumatics. Completed an approved MOLD Maker or Tool and Die Maker state apprentice ship program and/or certified by the U.S. Ability to perform machining operations with a specified degree of accuracy and within a timely manner, maintain close and exacting tolerances and finish requirements ensuring highest quality workmanship on all tools, gages, and fixtures with minimal scrap. Capable of creating a repeatable setup and working to tolerances of /-.0002" in controlled environment. Possesses 4 and 5 a
2026-3-23
Auburn, WA
& Die Maker. 2 years of experience with hydraulics and pneumatics. Completed an approved MOLD Maker or Tool and Die Maker state apprentice ship program and/or certified by the U.S. Ability to perform machining operations with a specified degree of accuracy and within a timely manner, maintain close and exacting tolerances and finish requirements ensuring highest quality workmanship on all tools, gages, and fixtures with minimal scrap. Capable of creating a repeatable setup and working to tolerances of /-.0002" in controlled environment. Possesses 4 and 5 a
2026-3-23
Everett, WA
reate charts, records, and graphs as assigned, and apply protective materials and parting agents to MOLDs, forms, and dies. Notify supervisors of equipment failures and malfunctions and make temporary MOLDs and dams from various materials as needed. Physical Demands and Potential Hazards: Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs. Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting. Handle
2026-3-23
Everett, WA
reate charts, records, and graphs as assigned, and apply protective materials and parting agents to MOLDs, forms, and dies. Notify supervisors of equipment failures and malfunctions and make temporary MOLDs and dams from various materials as needed. Physical Demands and Potential Hazards: Perform physical tasks that include lifting weights ranging from 10-15 lbs to 15-35 lbs. Engage in various movements such as reaching, handling, turning, twisting, lifting, lowering, climbing, balancing, bending, kneeling, crouching, and squatting. Handle
2026-3-23
Take Charge of Your Future Today!
2026-3-24
Public search utility limited to 10 most recent results. Please sign in or
register to view all search results & apply.
Aviation Job Search